SEDIMENTATION
Some basic definitions will aid in understanding the basic concept and aim of
sedimentation.
Sedimentation ,
also known as
settling
, may be defined as the removal of solid particles
from a suspension by settling under gravity.
Clarificat
ion
is a similar term, which usually refers specifically to the function of a
sedimentation tank in removing suspended matter from the water to give a clarified
effluent. In a broader sense, clarification could include flotation and filtration.
Thickenin
g
in sedimentation tanks is the process whereby the settled impurities are
concentrated and compacted on the floor of the tank and in the sludge

collecting hoppers.
Concentrated impurities withdrawn from the bottom of sedimentation tanks are called
sludge
, while material that floats to the top of the tank is called
scum
.
Application of sedimentation processes
In
water treatment
, sedimentation is commonly used to remove impurities that have been
rendered settleable by coagulation and flocculation, as when
removing turbidity and
color. Precipitates formed in processes such as water softening by chemical precipitation
are also removed by sedimentation.
In
municipal wastewater treatment
, sedimentation is the main process in primary
treatment, where it is re
sponsible for removing 50 to 70% of the suspended solids
(containing 25

40 per cent of the BOD) from the wastewater. After biological treatment,
sedimentation is used to remove the biological floc produced by microorganisms in these
processes, so that eff
luent quality will approach a standard suitable for discharge into
inland waterways. The removal of grit in the preliminary stage of treatment is commonly
carried out by means of a differential sedimentation process in which heavy grit is
permitted to set
tle while lighter organic matter is retained in suspension. Further
sedimentation after coagulation may be used in tertiary treatment.
Sedimentation is also required where phosphorus removal is effected by chemical
precipitation separately from primary o
r secondary treatment. Other less obvious
applications of sedimentation are in the separation of digested sludge from supernatant
liquor within secondary (unstirred) sludge digesters, and also in sludge lagoons.
An understanding of the principles governi
ng the various forms of sedimentation
behavior is essential to the effective design and operation of sedimentation tanks.
Classification of settling behavior
Several cases of settling behaviour may be distinguished on the basis of the
nature
of the
part
icles to be removed and their
concentration
. Thus, individual particles may be
discrete (sand grains) or flocculent (most organic materials and biological solids). Particle
concentrations may vary from very low through to high in which case adjacent parti
cles
are actually in contact. Common classifications of settling behaviour are:
Class I

Unlimited settling of discrete particles
Class II

Settling of dilute suspensions of flocculent particles
Class III

Hindered settling and zone settling
Class IV

Compression settling (compaction).
Sedimentation Class I

Unlimited settling of discrete particles.
Sedimentation is removal of discrete particles in such low concentration that each particle
settles freely without interference from adjacent particle
s (that is, unhindered settling).
When a particle settles in a fluid it accelerates until the drag force due to its motion is
equal to the submerged weight of the particle. At this point, the particle will have
reached its terminal velocity, V
p
.
A diagr
am for settling of an idealized spherical particle is shown below (Figure 2.4). V
p
is the particle settling velocity (m/s); D is the drag force; W is the submerged weight of
the particle; d is the diameter of the particle (m); A
p
is the projected area of
the particle
normal to the direction of motion (m
2
);
p
is the volume of the particle (m
3
);
is the
density of the particle (kg/m
3
);
p
is the fluid density (kg/m
3
);
is the dynamic viscosity
of the fluid (N.s/m
2
); and C
D
is the drag coefficient.
Figure 2.4 Definition diagram for particle terminal settling velocity
An expression for V
p
may be derived from the submerged weight of the settling particle,
W, and the fluid drag force, D.
The drag force on a particle is given by
D = C
D
A
p
v
s
2
/2
[2.1]
The submerged weight of the particle can be expressed as
W = (

l
)g
p
[2.2]
Since D = W, the above, after substituting A
p
and
p
for functions in terms of particle
diameter d and rearranging, results in the following ex
pression for
v
s
.
V
s
=
D
C
gd
l
l
)
(
3
4
[2.3]
In practice, it is found that C
D
is a function of the Reynolds Number, R
e
, and, for
spherical particles, it can be represented by the following expressions
R
e
< 1, C
D
=
24
R
e
1
< R
e
< 10
4
, C
D
=
24
R
e
+
3
(
R
e
)
1
2
+ 0.34
10
3
< R
e
< 10
5
, C
D
0.4
Substituting the above expression for R
e
< 1 (laminar flow) in Equation 2.3 and noting
that
R
e
=
l
v
s
d/
, results in the following equation, known as St
oke’s Law:
2
18
d
g
Vs
l
[2.4]
At high values of R
e
, where C
D
0.4, the equivalent expression is
V
s
=
3
.
33
(
l
)
l
gd
[2.5]
The general conclusion, that V
s
depends on a particular diameter, particle density and,
under some con
ditions, also on fluid viscosity and hence on temperature, is important in
understanding sedimentation behavior. Furthermore, in practical sedimentation tanks, the
terminal settling velocity is quickly reached, so, for non

flocculent particles and uniform
fluid flow the settling velocity is constant throughout the settling time. This fact can be
usefully applied to a study of settling in an
ideal sedimentation tank
to provide an
important design principle for sedimentation processes.
Idealized representa
tions of three common types of sedimentation tanks are shown in Fig
2.5: (a) rectangular horizontal flow, (b) circular radial flow and (c) upflow tanks.
The
ideal rectangular horizontal flow sedimentation tank
is considered divided into four
zones (Fig 2
.5a)
a
Inlet zone

in which momentum is dissipated and flow is established in a uniform
forward direction
b
Settling zone

where quiescent settling is assumed to occur as the water flows
towards the outlet
c
Outlet zone

in which the flow converges u
pwards to the decanting weirs or
launders
d
Sludge zone

where settled material collects and is moved towards sludge hoppers
for withdrawal. It is assumed that once a particle reaches the sludge zone it is
effectively removed from the flow.
The critica
l particle in the settling zone of an ideal rectangular sedimentation tank, for
design purposes, will be one that enters at the top of the settling zone, at point A, and
settles with a velocity just sufficient to reach the sludge zone at the outlet end of
the tank,
at point B. The velocity components of such a particle are V
h
in the horizontal direction
and V
s
, the terminal settling velocity, in the vertical direction.
From the geometry of the tank it is apparent that the time required for the particle to
settle, t
o
, is given by
t
o
=
H
V
p
= L/v
s
but, since V
s
= Q/WH, then V
s
= Q/WL, where Q is the rate of flow, and L, W and H are
the length, width and depth of the tank, respectively. Since the surface area of the tank,
A, is WL, th
en
V
s
= Q/A
According to this relationship, the slowest

settling particles, which could be expected to
be completely removed in an ideal sedimentation tank would have a settling velocity of
Q/A. Hence this parameter, which is called the
surface loading
rate
or
overflow rate
, is a
fundamental parameter governing sedimentation tank performance.
This relationship also implies that
sedimentation efficiency is independent of tank depth

a condition that holds true only if the forward velocity is low enough
to ensure that the
settled material is not scoured and re

suspended from the tank floor.
A similar analysis of an
ideal circular radial flow sedimentation tank
is summarized in
Fig 2.5b from which it is seen that the same relationship, V
s
= Q/A, is obtai
ned.
In an
ideal upflow sedimentation tank
(Fig 2.5c) it is apparent that a particle will be
removed only if its settling velocity exceeds the water upflow velocity. In this case the
minimum upflow velocity is given by the flow rate divided by the surfa
ce area of the tank
(Q/A), so once again the minimum settling velocity for a particle to be removed is V
s
=
Q/A.
In an ideal sedimentation tank with a horizontal or radial flow pattern, particles with
settling velocities < V
s
can still be removed partiall
y, but not in an ideal upflow tank.
Figure 2.5
Definition for ideal settling in sedimentation tanks
(a) rectangular horizontal flow tank,
(b) circular radial flow tank,
(c) upflow tank
Sedimentation Class II

settlement of flocculent pa
rticles in dilute suspension
It should be recognized that particles do collide and that this benefits flocculation and
hence sedimentation. In a horizontal sedimentation tank, this implies that some particles
may move on a curved path while settling fast
er as they grow rather than following the
diagonal line in Figure 2.5a. This favors a greater depth as the longer retention time
allows more time for particle growth and development of a higher ultimate settling
velocity. However, if the same retention t
ime were spread over a longer, shallower tank,
the opportunity for collision would become even greater because the horizontal flow rate
would become more active in promoting collisions. In practice, tanks need to have a
certain depth to avoid hydraulic
sh
ort

circuiting
and are made 3

6 m deep with retention
times of a few hours.
The advantage of low depths is exploited in some settling tanks by introducing baffles or
tubes. These are installed at an angle, which permits the settled sludge to slide down t
o
the bottom of the settler, even though any angle effectively increases the vertical
displacement between two plates.
Sedimentation Class III

hindered settling and zone settling and sludge blanket
clarifiers
As the concentration of particles in a sus
pension is increased, a point is reached where
particles are so close together that they no longer settle independently of one another and
the velocity fields of the fluid displaced by adjacent particles, overlap. There is also a net
upward flow of liquid
displaced by the settling particles. This results in a reduced
particle

settling velocity and the effect is known as
hindered settling
.
The most commonly encountered form of hindered settling occurs in the extreme case
where particle concentration is so
high that the whole suspension tends to settle as a
‘blanket’. This is termed
zone settling
, because it is possible to distinguish several
distinct zones, separated by concentration discontinuities. Fig 2.6 represents a typical
batch

settling column tes
t on a suspension exhibiting zone

settling characteristics. Soon
after leaving such a suspension to stand in a settling column, there forms near the top of
the column a clear interface separating the settling sludge mass from the clarified
supernatant. T
his interface moves downwards as the suspension settles. Similarly, there
is an interface near the bottom between that portion of the suspension, which has settled
and the suspended blanket. This interface moves upwards until it meets the upper
interface
, at which point settling of the suspensions is complete.
It is apparent that the slope of the settling curve at any point represents the settling
velocity of the interface between the suspension and the clarified supernatant. This once
again leads to th
e conclusion that in designing clarifiers for treating concentrated
suspensions (Class III), the surface loading rate is a major constraint to be considered;
unless the surface loading rate adopted is less than the zone

settling velocity (v
sz
) of the
influ
ent suspension, solids will be carried over in the effluent.
Figure 2.6 Settling column test for a suspension exhibiting zone

settling behavior
An important application of zone settling is the final design of sedimentation tanks of
activated sludge p
rocesses.
Hindered settling is also important in upflow clarifiers in water treatment. These units
often operate with a high concentration of solids (consisting of chemically

formed floc
and impurities) in suspension. By simple comparison with the ideal
upflow
sedimentation tank in Fig 2.5c, it may be seen that a suspension will be retained in an
upflow clarifier only if the settling velocity of the suspension interface, v
i
, is equal to the
upflow velocity of the water, v
u
. This is important because man
y practical settling tanks
are designed to maintain a high concentration of solids in suspension in order to take
advantage of the increased opportunity for particles to collide and agglomerate. This
assists in removing many of the very fine particles tha
t might otherwise be carried over in
the effluent.
In both these cases involving hindered settling of concentrated suspensions, the settling
velocity of the suspension, v
p
is dependent on its concentration; as this increases, v
p
decreases.
The relations
hip between the velocity of settling v
p
and the volumetric concentration of
the particles in the suspension has not yet been determined analytically for hindered
settling situations. It is therefore necessary to use empirical equations to define an
approx
imate relationship.
Many equations for this relationship have been proposed. The combined advantages of
mathematical simplicity and reasonable accuracy over a wide range of concentrations are
features of the empirical equation proposed by Richardson:
v
p
= v
s
n
[2.6]
where
= (1

c), the porosity of the suspension; c is the proportion of the total
suspension volume occupied by particles; and n is an index depending on the Reynolds
number and the size and shape of the particles.
For smooth spheres, th
e value of n varies from 4.65, for fully laminar flow conditions, to
about 2.5 for turbulent flow conditions around the particles. For irregular particles, it is
impracticable to determine volumetric concentration. The relationship may be modified
to
v
p
= v
s
(1

kc’)
[2.7]
where c’ is the concentration in mass units; k and n are parameters so chosen that the
resulting formula closely approximates the performance of the particular suspension.
Suitable values of k and n may be selected by plotting exper
imental values of log v
p
against values of log (1

kc’) for different selected values of k until a value is found to
give approximation to a straight line over an appropriate range. The corresponding value
of n may be calculated from the slope of the lin
e. The value of v
s
is given by the
extrapolated value of V when c = 0. Computer techniques can be useful in selecting (or
fitting) appropriate values of k and n to give a least

squares best fit.
Sedimentation Class IV

compression settling (compaction)
Very high particle concentrations can arise as the settling particles approach the floor of
the sedimentation tanks and adjacent particles are actually in contact. Further settling can
occur only by adjustments within the matrix, and so it takes place a
t a reducing rate. This
is known as
compression settling
or
consolidation
and is illustrated by the lower region of
the zone

settling diagram (Fig. 2.6). Compression settling occurs as the settled solids are
compressed under the weight of overlying solid
s, the void spaces are gradually
diminished and water is squeezed out of the matrix.
Compression settling is important in gravity thickening processes. It is also particularly
important in activated

sludge final settling tanks, where the activated sludge
must be
thickened for recycling to the aeration tanks and for disposal of a fraction of the sludge.
Design of sedimentation tanks
Sedimentation theory, predicts that, in the case of ideal settling, the main design
parameter to be considered is surfac
e loading rate, Q/A, because it represents the critical
particle settling velocity for complete removal. Practical Class II settling likewise
requires that adequate depth, H, or detention time, t, be provided in order to allow
flocculation to take place.
Uniform flow distribution cannot always be assumed in
practice owing to density currents, inadequate dissipation of momentum at the tank inlet
and drawdown effects at the effluent weirs. As a result of all these effects, surface
loadings and detention ti
mes derived from theory should be multiplied by a suitable
safety factor, typically 1.7 to 2.5, for practical design.
These considerations apply to all three types of tank commonly used for Class II
sedimentation, namely rectangular horizontal flow tanks,
circular radial flow tanks and
square upflow tanks.
In the case of Class III sedimentation, it was also shown that the surface loading rate is
the major parameter to be considered in design. Most of the following development of
theory therefore applies
to the design of both Class II and Class III sedimentation tanks.
The design of sedimentation tanks for a given flow rate Q, involves the selection of the
surface loading rate, Q/A, from which the required tank surface area may be calculated,
and either t
ank depth, H, or detention time, t. The relationships between the various
parameters concerned can be expressed as shown below.
For Q in m
3
/h and A in m
2
, the particle settling velocity, V
p
(m/h) is given by
V
p
= Q/A
[2.8]
Detention time (hours) is
AH
Q
, where H is depth (m)
[2.9]
The task of proportioning the tank, once values of the major parameters are chosen, can
be simplified by using a simple design chart (Fig 2.7) based on the above equations.
Alternative designs may be
quickly compared using this diagram, and effects of flow
variations on critical loading parameters be determined.
The
forward velocity
must also be considered in
rectangular tanks
, as excessive velocity
may result in the scouring and re

suspension of sett
led sludge. This requirement
influences the choice of length

to

width ratio for such tanks.
Forward velocity, V
h
(m/h), is given by
V
h
=
Q
WH
, where W is width of tank (m)
or,
V
h
=
L
t
, where L is length of ta
nk
[2.10]
Where L = length of tank (m)
t = detention time (hours)
This expression is represented in the upper left

hand quadrant of Fig 2.7 and, when read
in conjunction with the lower left

hand quadrant, gives the relationship between V
h
and
L:W rati
o for rectangular tanks. Values of L/W in practice range from 3 to 6, with a
value of 4 being common. For conversion, m/h x
1000
3600
= mm/s.
Weir loading rate
, Q/L
w
, is important in
rectangular tanks
. A single weir across the end
of th
ese tanks is considered too short to prevent the influence of the approach current
generated by the weir from extending upstream into the settling zone, with possible
disruption of the flow pattern through the tank. The length of the weir can be doubled b
y
placing a collection trough in the tank at the surface just before the end of the tank so that
the water can flow into the trough from both sides. If this is still insufficient for larger
tanks, the weir length can be increased by providing multiple sus
pended weir troughs,
designed to limit the maximum weir loading rate to about 12 m
3
/m.h (4

8 more typical).
The troughs usually take the shape of square fingers, projecting into the tank for a short
distance in the direction facing the oncoming water fl
ow. Water can then flow into the
troughs from all perimeters and the length of the trough is greatly extended by these so

called "fingers". The fingers all connect to an end trough or the final end weir, from
where the water flows to the sand filters..
In
circular radial flow tanks,
the weir loading rate on a single perimeter weir, is usually
within the normal range of values, so that suspended weirs are not necessary for small
circular tanks. The water then runs over the weir into a collection trough a
ll along the
whole perimeter of the tank. From there, it would run into one or more pipes or channels
to take the water to the sand filters. In larger radial tanks, the trough is placed within the
tank, a little distance from the outer edge. It is place
d at such a depth as to then make
both sides of the trough overflow weirs into the trough. This almost doubles the length of
the weir compared with a single, peripheral weir.
Precautions must be taken with outlet weirs in large tanks because the very s
mall depth of
the of flow over the weir under low flow conditions may be completely biased towards
one end of the settling tank due to slight construction inaccuracies (1mm can be
significant) or even wind pressures. These problems can be counteracted by
having a
sawtooth pattern on the weir to increase local depth, without affecting overall weir
loading rates and possible scouring of sediments.
Inlets
should be designed to dissipate the momentum and accurately distribute the
incoming flow in such a way a
s to establish the required flow pattern in the tank.
The diverging flow which occurs in circular outward flow tanks is inherently less stable
than the uniform forward flow in rectangular tanks, so that the design of the inlet stilling
box is important in
circular tanks. Excessive turbulence must be avoided in the inlet
region, since the sludge collection hopper in most types of tank is located immediately
beneath the inlet.
Sludge scrapers
must be provided in modern rectangular and large circular sedime
ntation
tanks, since it is not practicable to slope the floor sufficiently for gravitational self

cleaning.
One of the distinctive features of square hopper

bottomed tanks is that their sides are
steeply sloped so that they are self

cleaning. Sludge move
s down the walls by gravity to
collect at the bottom of the hopper, from where it can be drawn off under hydrostatic
head. The operating simplicity and lack of mechanical parts, which are features of these
tanks have led to their widespread use in small t
reatment plants. They are not generally
economical for larger plants, however, because of the rapid increase in hopper depth and
the corresponding cost increases which large tanks entail.
Horizontal flow sedimentation tanks
Some practical design data a
re provided for based on practical experiences. Various
features must be incorporated into the design to obtain an efficient sedimentation process.
The inlet to the tank must provide uniform distribution of flow across the tank. If more
than one tank ex
ists, the inlet must provide equal flow to each tank. Baffle walls are
often placed at the inlet to distribute even flow, by use of 100

200 mm diameter holes
evenly spaced across the width of the wall. Table 2.1 lists typical values.
Parameter
Design
value
Surface loading rate (m
3
/m
2
.d)
20

60
Mean horizontal velocity (m/min)
0.15

0.90
Water depth (m)
3

5
Detention time (min)
120

240
Weir loading rate (m
3
/m

d)
100

200
Table 2.1 Horizontal flow sedimentation tanks
Sludge blanket clarifiers
The
SBC is quite flexible and can be adopted for use in almost all site conditions. Figure
2.9 shows an interesting SBC system with plate settler arrangement. Here the usual
clariflocculator is also equipped with plate settler, thereby facilitating the soli
d removal.
The plate settler sits on top of the clariflocculator. Therefore, in most situations, this unit
does not need a subsequent filter unit.
Figure 2.9
Sludge blanket clarifiers
There are other forms of the SBC such as
a combined slurry recirculation type with
paddle flocculator or a SBC with plate settlers. SBCs with flocculator are also sometimes
called “clariflocculator” or other brand names. Another variation is where pulsed flow is
used to induce the required velo
city gradients in the clarifier to aid flocculation and such
clarifiers are then called “pulsator” or “superpulsator” clarifiers.
The clariflocculator seems to have some clear advantages, even though it looks slightly
sophisticated. It is the complicated
theory that is sophisticated, but not the reactor itself.
Some established detail designs of the SBC are available and could easily be incorporated
into any new designs. There are modified versions incorporating a plate settler and filter
to achieve ent
ire solid

liquid separation in the same unit itself. Most of these
modifications are made to suit the need of developing nations. Its use is highly
recommended in developing countries

especially in small community water supply
schemes

because of its
flexibility in capacity and its ability to take up widely varying
turbidity loads. It is highly suitable for package treatment plants, which are useful in
remote areas as well as in congested urban areas.
Example 2.4
Design a sedimentation tank for a
flow (Q) of 1000 m
3
/d. Determine the dimensions of
the tank and the outflow weir length. Assume suitable design criteria.
Solution
Assume an overflow rate (OFR) of 20 m
3
/m
2
.d as a typical value.
Area =
Q
OFR
=
1000
20
= 50 m
2
Assuming a detention time (DT) of 2 h,
Volume = Q x DT = 1000 x
2
24
= 83.3 m
3
Depth =
V
A
=
83
.
3
50
= 1.7 m
If width (W) to length (L) ratio is 1:3, then
A = 3W
2
= 50
W = 4.1 m
L =
3W = 12.3 m
Assuming a weir loading rate (WLR) of 160 m
3
/m.d,
Minimum weir length =
Q
WLR
=
1000
160
= 6.3 m
In order to accommodate this required weir length, a double trough at the end of the tank
would suffice, havin
g a length of 8m.
Example 2.5
Design a coagulation sedimentation tank with a continuous flow for treating water for a
population of 45,000 persons with an average daily consumption of 135 L/person.
Assume a surface loading rate of 0.9 m
3
m

2
h

1
and that
the weir loading rate is within
acceptable limits.
Solution
Average consumption = 135 x 45,000 = 6,075,000 L/d.
Allow 1.8 times for maximum daily consumption:
maximum daily consumption = 1.8 x 6,075,000 = 10,935m
3
/d.
Therefore, required surface are
a of the tank = (10,935/24)/0.9 = 506 m
2
.
Assume minimum depth of tank = 3.5 m.
Therefore, (settling) volume of the tank = 506 x 3.5 = 1772 m
3
.
Assume a length to width ratio of the tank of 3.5:1. Therefore the width would be
= 506/3.5w
2
m =
12m
Therefore, length of tank = 3.5 x 12 = 42 m.
Assuming a bottom slope of 1 in 60.
Depth of the deep end (at the influent end) = 3.5 + (1/60) x 42 = 4.2 m.
A floc chamber should be provided, at the entry to the tank, the capacity of which is
ass
umed to be 1/16 of the settling chamber, i.e.
= 1772/16 = 110.8 m
3
.
If the depth of floc chamber is 2.5 m, then
the area of the floc chamber = 110.8/2.5 = 44.3 m
2
.
The flocculation chamber also has a width equal to the sedimentation c
hamber, ie 12m.
Therefore, length of floc chamber = 45.562/12
3.8m.
It should be considered to add this length to the settling tank as it would otherwise reduce
the settling volume by 3.8/42 = 9%. However, considering that we have already provided
a
mply for maximum flow conditions, we could still fit the flocculation unit within the
tank.
Enter the password to open this PDF file:
File name:

File size:

Title:

Author:

Subject:

Keywords:

Creation Date:

Modification Date:

Creator:

PDF Producer:

PDF Version:

Page Count:

Preparing document for printing…
0%
Commentaires 0
Connectezvous pour poster un commentaire